Here down the page you will discover some decent resources in relation to Installing A Bathtub.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is readily available, the job can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the job and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This short article will help you install a brand-new bath tub in your washroom if you have actually currently gotten a new tub and don't require to transform the setup of your previous water system pipes.
Your tools and also product list must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in area between the faucet and also the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has been used at least once as this will settle it into its final position.
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to stop stress on the tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that report about A Step-by-Step Guide to Installing a Bathtub through a friend on our other site. Sharing is good. Helping others is fun. Thanks so much for taking the time to read it.
Book A Free Estimate